i have this inside, but i can't edit well. Doesn't work, what i have to change?
[code];;;---------------------------------------------------------------------------
%define ORANGE 00FFh ; ----------------
%define ORANGE_BLINK 0077h ;
%define ORANGE_BLIP 0011h ;
%define RED 00F0h ; YOU CAN
%define RED_BLINK 0070h ; ADD YOUR
%define RED_BLIP 0010h ; OWN
%define GREEN 000Fh ;
%define GREEN_BLINK 0007h ;
%define GREEN_BLIP 0001h ;
%define CYCLE 00EBh ; R,O,G,O
%define CYCLE_BLINK 0063h ; R,O,G,Off
%define LED_OFF 0000h ; ----------------
;;;---------------------------------------------------------------------------
%define NKP_LED_COLOR ORANGE ; < CHANGE IT HERE
%define ALTDASH_LED_COLOR RED ; < CHANGE IT HERE
%define PATCHBACK_LED_COLOR GREEN ; < CHANGE IT HERE
%define TRIBOOT_LED_COLOR CYCLE_BLINK ; < CHANGE IT HERE
;;;---------------------------------------------------------------------------
;%define KINGROACH_VERSION ; NDURE 3.X <<<<<<<<<<<<<<<<<<<<<<<<<
;;;---------------------------------------------------------------------------
;;; set fan speed with NKP modes only (if omitted then no fan speed change)
%define FAN_SPEED 30 ; < CHANGE IT HERE ( % fan speed / 2 ) 10-50 << changed !!!!
;;;---------------------------------------------------------------------------
;;; tray boot enable
;%define TRAY_BOOT
;;; tri-boot enable < dual is default, with tray_boot enabled
;%define TRI_BOOT
;;; close the tray when NOT tri-booting (faster booting then tri-boot)
%define CLOSE_TRAY_ALLWAYS
;;;---------------------------------------------------------------------------
;;; default Dashboard path (and tray boot closed) 2=C 1=E 6=F 7=G
;;;---------------------------------------------------------------------------
%define DASHBOARD_PATH '\Device\Harddisk0\Partition1\dash\xbmc\default.xbe'
%define DB_PATH2 '\Device\Harddisk0\Partition1\dash\default.xbe'
%define DB_PATH3 '\Device\Harddisk0\Partition1\UDATA\4d530017\62d648ebf155\default.xbe'
;;;---------------------------------------------------------------------------
;;; tray OPEN dash, when key IS patched back (must be a MS signed xbe)
;;; MUST BE PARTITION 1 or 2
;;;
;;; use this to patch back the MS key then boot PB_OPEN_PATH
;;;%define PATCH_BACK_MS_KEY
%define PB_OPEN_PATH '\Device\Harddisk0\Partition1\dash\UnleashX\default.xbe'
;;;---------------------------------------------------------------------------
;;; Dashboard path's for tray OPEN dash when using dual/tri-boot
;;; and NOT using PATCH_BACK_MS_KEY
;;;---------------------------------------------------------------------------
;;; tray OPEN dash, when key IS NOT patched back (must be a habibi signed xbe
;;; and MUST be partition 1 or 2 when NOT using OPEN_DASH_WITH_NKP)
;;;
%define OPEN_PATH '\Device\Harddisk0\Partition1\dash\UnleashX\default.xbe'
;;; use this to enable all of NKP (disable to boot some other HACK)
%define OPEN_DASH_WITH_NKP
;;; use this to disable shadowC in open (alt) dash
;%define OPEN_DASH_shadowC_OFF
;;;---------------------------------------------------------------------------
;;; VIDEO patches:
;;;
;;; VIDEO_FORCE_RGB = Patches kernel to output RGsB video signal (RGB with
;;; sync on green) if HDTV AV pack is detected. Intended for
;;; connecting the Xbox to VGA monitor. Connect AV pack Y output
;;; to monitor green input, Cr to monitor red input and Cb to
;;; monitor blue input. The monitor must support sync on green.
;;;
;;; VIDEO_FORCE_PROGRESSIVE = Patches kernel to convert 480i video modes to
;;; 480p if HDTV AV pack is detected. Note that when using HDTV AV
;;; pack, progressive scan video output will be forced even if 480p
;;; video support is disabled in msdash.
;;;
;;; Not enabled by default.
;%define VIDEO_FORCE_RGB
%define VIDEO_FORCE_PROGRESSIVE
;;; Flicker Filter Patch (interlaced composite video only)
;;;
;;; When enabled any call to set the flicker filter value will be
;;; replaced by a call with the value FLICKER_FILTER_VALUE.
;;;
;;; Takes values in the range 0 (off) to 5 (max filter).
;;;
;;; Flicker filter patching is not enabled by default.
;%define FLICKER_FILTER
;%define FLICKER_FILTER_VALUE 2
;;;---------------------------------------------------------------------------
;;; used to boot the dash only
;;;
%define NORMAL_BOOT_ALWAYS
[code]
Author
Topic: Restore Ms Dash And Unleashx And Add Linux Distro (Read 1011 times)