Print

[theboyfromthemoon]

Hey man, just write a simple scheme, which wires goes where...do I have to open the big connector with optical output (it's a big mess inside), or just the d-terminal connector ?

[theboyfromthemoon]

I succed, after working 6 ours on...that was hard, I completely removed the wires from the main connector, rewired them using the vga scheme, rebuild the pcb inside the connector to keep the switch for normal TV.

[Adamq]

  Well done see its not that hard to work out what to do once you get into it    

[clownbow]

QUOTE(Adamq @ Dec 24 2005, 03:00 PM)

Hi theboyfromthemoon

RGB terminal (D-Sub 15-pin connector)

pin-1 R(Pr/Cr)
pin-2 G or sync on green (y)
pin-3 B (Pb/Cb)
pin-4 No Connection
pin-5 No Connection
pin-6 R GND (Pr/Cr GND)
pin-7 G GND (Y GND)
pin-8 B GND (Pb/Cb GND)
pin-9 No Connection
pin-10 GND
pin-11 No Connection
pin-12 [SDA]
pin-13 H SYNC or H/V composite sync
pin-14 V sync [V.CLK]
pin-15 [SCL]

Hope this helps if you get stuck let me know and i will take a pic of the plug so you can see how it's wired up

can you please post pics thanks. is it correct that you only have to connect 3 wires to the vga plug?

[clownbow]

QUOTE(clownbow @ Jan 8 2006, 02:31 PM)

can you please post pics thanks. is it correct that you only have to connect 3 wires to the vga plug?

so no one has proof that this mod actually works.

[Adamq]

No mate it dont work i dont have anything better to do than to post bullshit in forums   if you cant figure out how to wire up a simple 15-pin connector from the diagram and the pin out instructions i have already posted maybe you should just go buy a cable  

[clownbow]

QUOTE(Adamq @ Jan 11 2006, 09:59 AM)

No mate it dont work i dont have anything better to do than to post bullshit in forums   if you cant figure out how to wire up a simple 15-pin connector from the diagram and the pin out instructions i have already posted maybe you should just go buy a cable  

so you saying that you would post pics is BS.?

[Adamq]

Ok do u know any sites i can upload pics to and i will post them

[clownbow]

QUOTE(Adamq @ Jan 11 2006, 01:37 PM)

Ok do u know any sites i can upload pics to and i will post them

sorry for sounding harsh.; i know nothing about modding leads, and don't want to mess it up. here is a site i use.
http://imageshack.us/

[clownbow]

ok i hooked the wires to a cut vga lead. and i can confirm that this cable mod doesn't work!!!

[Adamq]

QUOTE(clownbow @ Jan 12 2006, 04:25 AM)

ok i hooked the wires to a cut vga lead. and i can confirm that this cable mod doesn't work!!!

OK  









Maybe you should try again or get someone that knows what they are doing because it works 100%

[Adamq]

QUOTE(clownbow @ Jan 12 2006, 04:25 AM)

ok i hooked the wires to a cut vga lead. and i can confirm that this cable mod doesn't work!!!

Got that plug wired up and working yet clowboy  

[theboyfromthemoon]

Just fallow the vga scheme, don't forget to wire all the grounds to the main ground  and connect to the vga connector RGB wires, ground wires, H & V sync. There are 3 thin wires that goes to the optical connector, keep them (+5, spdif, gnd). Other thin wires remove (this way the switch has no function). Be carefull at mod wires wich gives the vga, hdtv, composite signal. If you want to keep the switch, it needs some rebuilding the small pcb inside the main xbox connector. I want to post a scheme, but can't find any file uploader...

@Adamq: In the last picture the screen sais D3 (1125i / 1080i). This is a HDTV resolution not VGA...

[ico78]

Guys!

Please help!

Where I should connect wires from 8, 9, 11, 12, 14 in D component to VGA connector?

If possible, please give me scheme where exactly connect all wires from D to VGA

Thanks

[Shippy]

ico78, did you ever figure out which wires go where?  I just picked up a Japanese 360 and was considering doing this mod.