xboxscene.org forums

Xbox360 Forums => Xbox 360 Hacking Forums => Technical DVD-ROM and Modified DVD Firmware Forum => Topic started by: warnec on March 08, 2009, 04:44:00 PM

Title: How Do I Update 1.5->1.51?
Post by: warnec on March 08, 2009, 04:44:00 PM
Hi. I bought X360 with ms28 drive spoofed as liteon with 1.4 ixtreme. I flashed it to 1.5 with iprep, but I flashed my friend's one with jungleflasher (just like mine, ms28 spoofed as liteon, 1.4->1.5)

Now I want to update firmware from 1.5 to 1.51 and I'm unsure what to do.

I have the newest JungleFlasher and the tutorial. The tutorial, however, says very little about unlocking samsung ms28 with ix 1.5 - only one small image. So it's possible I unlocked it incorrectly and that's why it didn't work.

What I did:

1) Connected 360 drive to VIA SATA Card via SATA cord
2) 360 drive connected to X360 via power cord
3) Ran both PC and Xbox
4) Ran JungleFlasher
5) Clicked MTKFlash32 Tab, clicked the right port in MTKFlash32 tab (my drive appeared)
6) Ejected 360 drive tray
7) Pulled the 360 drive power cord out
8 )Pushed the tray halfway in
9) Inserted 360 drive power cord

There was no data in Flash Chip Properties, all fields were empty.

Now, that's interesting - when I flashed 1.4->1.5, I'm almost 100% sure it said it's samung ms28, and now in drive properties it says it's LiteOn!

10) Clicked Intro/Device ID

In Drive Properties "Drive in Vendor Mode!" appeared. No info in Flash Chip Properties, however. All fields empty. No signal of the 0x70 status.

11) Clicked "Read"

I got message "Invalid drive status" or something similar.

Any ideas?

PS Or maybe, because it is spoofed as Liteon, I should flash it as liteon?
http://forums.afterdawn.com/thread_view.cfm/755062

This post has been edited by warnec: Mar 8 2009, 11:46 PM
Title: How Do I Update 1.5->1.51?
Post by: Traviss63 on March 08, 2009, 05:01:00 PM
In the MTKFlash tab at the top click the blue text that says Activate.iso and it will send you to a download location for a disc image which needs to be burned to a Dual Layer dvd with NO LAYER BREAK. I used Nero to burn and it failed to finalize but the disc worked.
After burning it insert it into your samsung drive wait 30 seconds then start Jungleflasher go to MTKFlash tab and click device intro and you should get a valid status.

EDIT: Just noticed you said 1.5 to 1.51 I think that the activate.iso is for 1.4 and below but it may be worth a try

This post has been edited by Traviss63: Mar 9 2009, 12:03 AM
Title: How Do I Update 1.5->1.51?
Post by: warnec on March 08, 2009, 05:05:00 PM
I've got this disc. I used it to update 1.4 -> 1.5. I won't use it, since it is only for ix14 or lower.
Title: How Do I Update 1.5->1.51?
Post by: 10pmstalker on March 08, 2009, 06:40:00 PM
I have the same problem. In Drive Properties it says Vendor: No Drive Detected. I also have no idea how to find the correct port to select?

Im not trying to hijack your post, Just hoping you can give me a little help about the same setup (drive spoofed as liteon with 1.5 firmware)
Title: How Do I Update 1.5->1.51?
Post by: warnec on March 09, 2009, 12:33:00 PM
Now, when I tried it for the second time, after clicking "Intro/Device ID" it shows me :
CODE

Flash Chip Properties:
Vendor ID: 0xBF
Device ID: 0xB6
Name: SST(SST39SF020)
Size: 262144 bytes
Type: Parallel flash with Status 0x70


And:
CODE

Parallel flash found with status 0x70

Sending Device ID request to port 0xCE00
Manufacturer ID: 0xBF
Device ID: 0xB6
Flash Name: SST(SST39SF020)
Flash Size: 262144 bytes

Reading Bank 0:..


And JF hangs.
Title: How Do I Update 1.5->1.51?
Post by: TheKingABC on March 09, 2009, 01:28:00 PM
QUOTE(warnec @ Mar 9 2009, 08:09 PM) View Post

Now, when I tried it for the second time, after clicking "Intro/Device ID" it shows me :
CODE

Flash Chip Properties:
Vendor ID: 0xBF
Device ID: 0xB6
Name: SST(SST39SF020)
Size: 262144 bytes
Type: Parallel flash with Status 0x70


And:
CODE

Parallel flash found with status 0x70

Sending Device ID request to port 0xCE00
Manufacturer ID: 0xBF
Device ID: 0xB6
Flash Name: SST(SST39SF020)
Flash Size: 262144 bytes

Reading Bank 0:..


And JF hangs.


I have more or less the same problem. Should we flash it with the lite-on firmware? Or sammy? Thanks!
Title: How Do I Update 1.5->1.51?
Post by: that360guy on March 09, 2009, 01:43:00 PM
If it's a samsung drive then you need to use the samsumg firmware. I would actually use the latest version of toolbox to make the firmware and spoof it.

I would do your dumping and flashing in dos using dosflash, then you don't have to worry about hangups for the most part.
Title: How Do I Update 1.5->1.51?
Post by: TheKingABC on March 09, 2009, 03:01:00 PM
QUOTE(that360guy @ Mar 9 2009, 09:19 PM) View Post

If it's a samsung drive then you need to use the samsumg firmware. I would actually use the latest version of toolbox to make the firmware and spoof it.

I would do your dumping and flashing in dos using dosflash, then you don't have to worry about hangups for the most part.


Thanks for clearing up. Do I still need to use the activate.iso to get the drive in the correct mode?
Title: How Do I Update 1.5->1.51?
Post by: warnec on March 09, 2009, 04:31:00 PM
activate.iso is only for ixtreme <=1.4

See my topic here:
http://forums.maxcon...ad.php?t=137599

Somebody advised to use dosflash 32. It does not work, however. If it fails, I'll use dosflash (command line)
Title: How Do I Update 1.5->1.51?
Post by: TheKingABC on March 10, 2009, 06:19:00 AM
QUOTE(warnec @ Mar 10 2009, 12:07 AM) View Post

activate.iso is only for ixtreme <=1.4

See my topic here:
http://forums.maxcon...ad.php?t=137599

Somebody advised to use dosflash 32. It does not work, however. If it fails, I'll use dosflash (command line)


How do you know that the activate.iso is only for <= 1.4? Only because it's in the manual? Maybe the text has not been updated and should it also be used for 1.5? The drive needs to be in the correct mode and the iso will do this. It might be still needed for 1.5? Or not?
Title: How Do I Update 1.5->1.51?
Post by: warnec on March 10, 2009, 07:51:00 AM
Well, i'll give t a shot now, but I doubt it'll work.

EDIT.: It doesn't work.

This post has been edited by warnec: Mar 10 2009, 03:00 PM
Title: How Do I Update 1.5->1.51?
Post by: warnec on March 10, 2009, 09:47:00 AM
Ok, I updated successfully using this guide:
http://www.360mods.n...u...pic&t=11945
Title: How Do I Update 1.5->1.51?
Post by: TheKingABC on March 10, 2009, 02:10:00 PM
QUOTE(warnec @ Mar 10 2009, 05:23 PM) View Post

Ok, I updated successfully using this guide:
http://www.360mods.n...u...pic&t=11945


You used a VIA card with VT6421A chipset? I tried this guide but it does not work, I guess because I try it with a Intel ICH chip. I will order a VIA board and try again.
Title: How Do I Update 1.5->1.51?
Post by: warnec on March 11, 2009, 10:30:00 AM
Yes, it's a card with VIA VT6421A chipset, but I also used one with VT6421L before.

They both work.
Title: How Do I Update 1.5->1.51?
Post by: TheKingABC on March 11, 2009, 12:35:00 PM
QUOTE(warnec @ Mar 11 2009, 06:06 PM) View Post

Yes, it's a card with VIA VT6421A chipset, but I also used one with VT6421L before.

They both work.


I don't need to do something in order to get the drive responding to iprep? No half-open or other things? Power on PC and then connect SATA cable when I'm in Dos? That's it? Thanks again!

Oh, and should I install the drivers in Windows when I would like to use Jungleflasher? Or only portio?
Title: How Do I Update 1.5->1.51?
Post by: xaudiox on March 11, 2009, 01:07:00 PM
Pull the power while the drive is ejecting so it actually stops half way, there is no need to touch it.
Then reconnect the power, the drive tray will stay where it is.

Also when you are done flashing make sure the drive will open/close properly (you may have to close it yourself first)
Otherwise it might be stuck in vendor mode.

Works for me every time.

This post has been edited by xaudiox: Mar 11 2009, 08:13 PM
Title: How Do I Update 1.5->1.51?
Post by: warnec on March 11, 2009, 02:48:00 PM
Well, the half tray trick is only required with Jungleflasher, AFAIK.

I just followed Textbook's tutorial (the one I linked to)

So I turned off whole xbox, selected the drive in DOS, waited 10 seconds, turned xbox back on. No pulling the power cord of 360 drive or ejecting tray, only power cycling whole xbox with power button.

And yes, I used drivers for the VIA card. (I don't know if I needed it)
Title: How Do I Update 1.5->1.51?
Post by: TheKingABC on March 11, 2009, 03:02:00 PM
QUOTE(warnec @ Mar 11 2009, 10:24 PM) View Post

Well, the half tray trick is only required with Jungleflasher, AFAIK.

I just followed Textbook's tutorial (the one I linked to)

So I turned off whole xbox, selected the drive in DOS, waited 10 seconds, turned xbox back on. No pulling the power cord of 360 drive or ejecting tray, only power cycling whole xbox with power button.

And yes, I used drivers for the VIA card. (I don't know if I needed it)


Thanks Warnec. I will receive the VIA board tomorrow and then I will give it a shot.
Title: How Do I Update 1.5->1.51?
Post by: joey3002 on March 12, 2009, 09:34:00 AM
QUOTE(TheKingABC @ Mar 11 2009, 10:38 PM) View Post

Thanks Warnec. I will receive the VIA board tomorrow and then I will give it a shot.


thekingABC - any update?
Title: How Do I Update 1.5->1.51?
Post by: Gir489 on March 12, 2009, 12:21:00 PM
The half-open trey never works for me on any of my Samsungs.

I always have to do the bad flash method for upgrading.
Title: How Do I Update 1.5->1.51?
Post by: joey3002 on March 12, 2009, 12:33:00 PM
QUOTE(Gir489 @ Mar 12 2009, 07:57 PM) View Post

The half-open trey never works for me on any of my Samsungs.

I always have to do the bad flash method for upgrading.


what do you mean, "bad flash method" ?

thanks
Title: How Do I Update 1.5->1.51?
Post by: warnec on March 13, 2009, 05:26:00 AM
bad flash = flashing/dumping with via card and 10 second trick (turning xbox off, choosing drive in dos, waiting 10 seconds, then turning xbox on)