xbox-scene.com archived forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

xbox-scene.com forum restored.  registration disabled.  thanks to xboxexpert for the db dump and netham45 for cleaning it up!

Pages: [1] 2 3 ... 8

Author Topic: Simple Db-25/cat5 Lpt Nand Dump/flash Cable Tut  (Read 2207 times)

sabbath_dude

  • Guest
Simple Db-25/cat5 Lpt Nand Dump/flash Cable Tut
« on: September 12, 2009, 08:26:46 AM »


I can't take any credit for this idea as I know a few other people round here already use this setup. Same goes for the info on where to solder the various wires etc. I've simply gathered all the required info and tried to put it together here in one noob friendly tut  smile.gif .

Anyway, the plan is to create one neat and tidy cable that can be used to dump and flash your 360's NAND by simply plugging into a specially created Ethernet port. The benefits of this are that the cable can be used on multiple 360's without the need for resoldering or messy wires hanging out your box.
IPB ImageIPB ImageIPB Image

What you'll need
IPB Image
RJ45 Ethernet Network LAN Cable Extension Adapter - I bought mine on eBay at �3 for 10
Standard Cat5 patch cable (Not a crossover cable, see HERE about the difference)
D-Sub hood 25-way - I bought mine in Maplin for about �1.60 part #FP29G
DB25 25-way male plug - I bought mine in Maplin for about �1.50 part #YQ48C

Other things you'll need are 5x100 ohm resistors and possibly some zip ties for securing your wiring.

IPB Image
The idea here is pretty simple. All you're going to do is match the colours marked on the Xbox motherboard with the db25 plug. But instead of going straight from one to the other you're going to have an Ethernet cable extender in the middle. This will allow you to unplug/connect you're 360 to your PC quickly and whenever you want.

Cut your Cat5 cable in half and prepare both ends for soldering. I recommend keeping the cable between your Xbox and PC as short as possible. After a bit of trial and error I found 35-40cm to be about right. The cable inside your Xbox should also be as short as possible.
IPB Image

IPB Image

Solder your wires to the Xbox motherboard following my diagram above. Find a good spot to place your Ethernet extender and secure it in place. I cut a hole in the metal shielding behind the DVD drive and hot glued the extender in place. I then cut a small hole on the outer case under the hard drive to allow easy access to the port whenever needed. When not in use the port is hidden under the hard drive.  

Next you need to solder the other half of your Cat5 cable to the DB25 plug. Be careful to match up with the correct wires you soldered to the 360's motherboard!. Depending on your PC you may or may not need to install some 100 ohm resistors on pins 1,2,14,16 and 17. Some people will get away without them but in my case the NAND would not dump correctly unless I had resistors in place. You may also need to fit a switching diode to pin 11 if you are not getting the correct FlashConfig (normal config being 0x1198010). I had no issues so there was no need for me to fit the diode.
IPB Image
Just so there is no confusion on which pin is which.....
IPB Image

Fit your D-sub hood and you're all done  biggrin.gif .
IPB Image

*Update*
I just wanted to add some pics of the interesting configurations/variations people have come up with to dump and flash their 360's....
Reusable easy solder solution by garlon
http://img192.images...85/lptcable.jpg
My easy solder cat5 attachment using garlon's idea
http://i784.photobuc..._dude6/att3.jpg
http://i784.photobuc..._dude6/att2.jpg
http://i784.photobuc..._dude6/att1.jpg
Super clean low profile solution by fahrenheit
http://i3.photobucke...it/RJ45_PCB.jpg
http://i3.photobucke...VDclearance.jpg
http://i3.photobucke...it/LPTwired.jpg
http://i3.photobucke...FinishedLPT.jpg
Integrated nand write protect switch by Chemodile
http://i195.photobuc...p-internalS.jpg
http://i195.photobuc...i_nwp-sideS.jpg
http://i195.photobuc...i_nwp-caseS.jpg
http://i195.photobuc..._swp-cableS.jpg




Edited by sabbath_dude, 02 February 2010 - 01:44 PM.


Logged

4NZ33

  • Guest
Simple Db-25/cat5 Lpt Nand Dump/flash Cable Tut
« Reply #1 on: September 12, 2009, 08:31:03 AM »


Similar to what I did but yours looks much more neat than mine.

Very Nice.

 smile.gif




Logged

Relapse75

  • Guest
Simple Db-25/cat5 Lpt Nand Dump/flash Cable Tut
« Reply #2 on: September 12, 2009, 11:16:24 AM »


This is cool and all makes it easy to flash, but you do know that the new version of Xell is update-able via a USB drive. And you should never have to connect to the pc again, there is even a fail safe where you can revert from a bad update using the back usb port.  I have removed the LPT flashing hardware from my boxes just because of this.




Logged

sabbath_dude

  • Guest
Simple Db-25/cat5 Lpt Nand Dump/flash Cable Tut
« Reply #3 on: September 12, 2009, 12:17:03 PM »


Similar to what I did but yours looks much more neat than mine.

Very Nice.

 smile.gif
Thanks  smile.gif .
This is cool and all makes it easy to flash, but you do know that the new version of Xell is update-able via a USB drive. And you should never have to connect to the pc again, there is even a fail safe where you can revert from a bad update using the back usb port.  I have removed the LPT flashing hardware from my boxes just because of this.
Yes I know Xell is now update-able via USB but If you're like me and still want to flash the original Microsoft dash back from time to time then this is very handy. My main console is PAL and there are a couple of games not available to me so it's really nice to be able to switch the region code as and when needed  biggrin.gif . The other main benefit I find is being able to use the same cable to quickly switch from one 360 to another. Before I had to desolder/resolder which was a pain in the balls and wasted time.

Besides that I personally haven't had much luck in getting Xell to update from USB. I realise it's early days yet and things will no doubt become more stable/streamlined but it's still nice to have permanent, quick and easy access to the NAND.





Logged

Cisk

  • Guest
Simple Db-25/cat5 Lpt Nand Dump/flash Cable Tut
« Reply #4 on: October 08, 2009, 10:33:54 AM »


Whoa this is impressive, just the handy idea i was looking for.


Thanks, will be doing this later.




Logged

eyric101

  • Guest
Simple Db-25/cat5 Lpt Nand Dump/flash Cable Tut
« Reply #5 on: November 23, 2009, 10:30:11 AM »


I love this, very tidy.  If this forum gave rep you get + from me!




Logged

amexie

  • Guest
Simple Db-25/cat5 Lpt Nand Dump/flash Cable Tut
« Reply #6 on: November 23, 2009, 12:10:57 PM »


what i have done with mine is just put and lpt port on the back of the 360 ill tack a pic later
so much easier than making a cable aswell




Logged

ffriozi

  • Guest
Simple Db-25/cat5 Lpt Nand Dump/flash Cable Tut
« Reply #7 on: November 24, 2009, 03:44:03 PM »


First Thanks A lot !!!

i have a question... i have xbox Model JASPER 512 mb. what is this? do i need do this?

IPB Image

Thanks !




Logged

Poopchute

  • Guest
Simple Db-25/cat5 Lpt Nand Dump/flash Cable Tut
« Reply #8 on: November 24, 2009, 03:51:04 PM »


So is it safe to leave these wires permenantly soldered into the board?  What about soldering 2 small pin headers into the 7-wire spots so a person could easily solder into the board without risking solder splashes and scratched traces?




Logged

ffriozi

  • Guest
Simple Db-25/cat5 Lpt Nand Dump/flash Cable Tut
« Reply #9 on: November 24, 2009, 03:55:45 PM »


Nvm that ohm is for Jtag exploit. !




Logged

akirhol

  • Guest
Simple Db-25/cat5 Lpt Nand Dump/flash Cable Tut
« Reply #10 on: November 24, 2009, 08:42:55 PM »


Loooove this tutorial... I did this on Sunday and it worked out perfectly. I didn't leave the coupler in the case though, just tucked the network cable in under the DVD drive.

Thanks for posting this!

I did have a question though, other tuts reference using a switching diode on one of the solder points... I did it without and it worked fine on my Xenon board... is this a requirement for later boards? Is there a specific purpose for it?




Edited by akirhol, 25 November 2009 - 05:45 AM.


Logged

YaPaY

  • Guest
Simple Db-25/cat5 Lpt Nand Dump/flash Cable Tut
« Reply #11 on: November 25, 2009, 05:33:35 AM »


First Thanks A lot !!!

i have a question... i have xbox Model JASPER 512 mb. what is this? do i need do this?

IPB Image

Thanks !


Same question here. I have Falcon board.




Logged

ffriozi

  • Guest
Simple Db-25/cat5 Lpt Nand Dump/flash Cable Tut
« Reply #12 on: November 25, 2009, 08:58:01 AM »


Same question here. I have Falcon board.


bro that is for Jtag exploit !! dont work anymore so dont worry smile.gif




Logged

Poopchute

  • Guest
Simple Db-25/cat5 Lpt Nand Dump/flash Cable Tut
« Reply #13 on: November 25, 2009, 11:43:12 PM »


I don't understand why people are sayin that's for the JTAG thing don't worry... Isn't that what we're doin this for?





Logged

YaPaY

  • Guest
Simple Db-25/cat5 Lpt Nand Dump/flash Cable Tut
« Reply #14 on: November 26, 2009, 04:57:53 AM »


I don't understand why people are sayin that's for the JTAG thing don't worry... Isn't that what we're doin this for?


Confused  sleeping.gif

Should I make Jtag thing, too for hdd uncripple or not. I'm newbie and really confused. And second question which ethernet color to where. (orange-white, orange, green-white etc.)

I opened case and I'm waiting for a reply. If JTAG thing neceassary I will give up.




Logged
Pages: [1] 2 3 ... 8
 

Page created in 0.192 seconds with 14 queries.